Nassau County · Public water (Plainview Water District)
Water Quality in Plainview, NY — What’s In Your Water
Plainview's water is supplied by Plainview Water District. The most recent published results show Combined Radium 226/228 at 5.45 pCi/L (above the limit), Copper at 0.20 mg/L. Every figure below is shown against its NY or EPA limit and cited to its source.
Reported contaminants
Plainview water, by the numbers
ND means not detected. Units: µg/L is micrograms per liter (parts per billion); ng/L is nanograms per liter (parts per trillion); mg/L is milligrams per liter (parts per million). Status uses the words below, near, exceeds, or trace — not color alone.
Source: Plainview Water District 2025 Annual Water Quality Report (opens in a new tab)
| Substance | Detected level | Limit | Status |
|---|---|---|---|
| PFAS | |||
| PFOA (about this substance) | 3.27 ng/LRange ND–3.27 | 10NYS MCL | Below limit |
| PFBA (about this substance) | 18.6 ng/LRange ND–18.6 | No regulatory limit | — |
| PFHxA (about this substance) | 2.02 ng/LRange ND–2.02 | No regulatory limit | — |
| PFPeA (about this substance) | 2.06 ng/LRange ND–2.06 | No regulatory limit | — |
| Industrial solvents & 1,4-dioxane | |||
| 1,4-Dioxane (about this substance) | 0.61 µg/LRange ND–0.61 | 1.0NYS MCL | Below limit |
| 1,1,1-Trichloroethane (about this substance) | 1.8 µg/LRange ND–1.8 | 5EPA MCL | Below limit |
| Nitrate, metals & inorganics | |||
| Combined Radium 226/228 (about this substance) | 5.45 pCi/LRange 3.03–5.45Highest single result 5.45 pCi/L. The report's violation column is No. | 5EPA MCL | No violation reported |
| Nitrate-Nitrite (as N) (about this substance) | 8.5 mg/LRange 0.68–8.5 | 10EPA MCL | Near limit |
| Nitrate (about this substance) | 8.4 mg/LRange 0.66–8.4 | 10EPA MCL | Near limit |
| Turbidity (about this substance) | 3.8 NTURange ND–3.8 | 5EPA MCL | Below limit |
| 1,1-Dichloroethane (about this substance) | 3.6 µg/LRange ND–3.6 | 5EPA MCL | Below limit |
| Odor (about this substance) | 2.0 UnitsRange ND–2.0 | 3NYS secondary standard | Below limit |
| Color (about this substance) | 8.0 UnitsRange ND–8.0 | 15NYS secondary standard | Below limit |
| Perchlorate (about this substance) | 5.8 µg/LRange ND–5.8 | 18NYS MCL | Below limit |
| Thallium (about this substance) | 0.45 µg/LRange ND–0.45 | 2EPA MCL | Below limit |
| Gross alpha (about this substance) | 3.23 pCi/LRange ND–3.23 | 15EPA MCL | Below limit |
| Chloride (about this substance) | 40.5 mg/LRange 11.9–40.5 | 250NYS secondary standard | Below limit |
| Formaldehyde (about this substance) | 5.5 µg/LRange ND–5.5 | 50EPA MCL | Below limit |
| Nitrite (about this substance) | 0.1 mg/LRange ND–0.1 | 1EPA MCL | Below limit |
| Gross beta (about this substance) | 4.76 pCi/L (6)Range 0.11–4.76 | 50EPA MCL | Below limit |
| Uranium (about this substance) | 1.62 µg/LRange ND–1.62 | 30EPA MCL | Below limit |
| Sulfate (about this substance) | 11.4 mg/LRange ND–11.4 | 250NYS secondary standard | Below limit |
| Barium (about this substance) | 0.059 mg/LRange 0.004–0.059 | 2EPA MCL | Below limit |
| Copper (about this substance) | 0.016 mg/LRange ND–0.016 | 1.3EPA action level | Below limit |
| Zinc (about this substance) | 0.025 mg/LRange ND–0.025 | 5NYS secondary standard | Below limit |
| Iron (about this substance) | 0.23 mg/LRange ND–0.23 | 300NYS secondary standard | Below limit |
| Manganese (about this substance) | 0.094 mg/LRange ND–0.094 | 300NYS secondary standard | Below limit |
| Calcium (about this substance) | 66.8 mg/LRange 2.2–66.8 | No regulatory limit | — |
| Magnesium (about this substance) | 3.1 mg/LRange 1.2–3.1 | No regulatory limit | — |
| Nickel (about this substance) | 0.014 mg/LRange 0.0013–0.014 | No regulatory limit | — |
| Sodium (about this substance) | 13.9 mg/LRange 6.5–13.9 | No regulatory limit | — |
| Ammonia (as N) (about this substance) | 2.9 mg/LRange ND–2.9 | No regulatory limit | — |
| Alkalinity (about this substance) | 123.0 mg/LRange ND–123.0 | No regulatory limit | — |
| Total Dissolved Solids (about this substance) | 274.0 mg/LRange 27.0–274.0 | No regulatory limit | — |
| Lead & copper | |||
| Lead (about this substance) | ND µg/L(90th percentile)Range ND–2.5 | 15EPA action level | Trace — detected in some samples |
| Copper (about this substance) | 0.20 mg/L(90th percentile)Range ND–0.4 | 1.3EPA action level | Below limit |
| Disinfection byproducts | |||
| Total Trihalomethanes (about this substance) | 1.3 µg/LRange ND–1.3 | 80EPA MCL | Below limit |
| Chlorate (about this substance) | 18.5 µg/LRange ND–18.5 | No regulatory limit | — |
Water characteristics
| Substance | Detected level | Limit | Status |
|---|---|---|---|
| Free Chlorine (about this substance) | 1.03 mg/LRange 0.57–1.03 | 4.0EPA MRDL | Below limit |
| pH (about this substance) | 8.3 UnitsRange 4.4–8.3 | No regulatory limit | — |
| Hardness (total) (about this substance) | 180.0 mg/LRange 10.3–180.0 | No regulatory limit | — |
| Calcium hardness (about this substance) | 167.0 mg/LRange 5.6–167.0 | No regulatory limit | — |
Status reflects the average of all samples. Individual readings may be higher; see range.
Where the report prints both an average and a range, the status column here is judged on the average; where it prints a maximum or a 90th-percentile result, that figure is used. The report carries 1 notice: No violations reported: 'We are pleased to report that our drinking water meets all Federal and State requirements.' (page 2). All table rows print Violation 'No'. Footnote (9): initial point-of-entry 1,4-dioxane result of 1.4 ug/L at Well No. 1-2 averaged down to 0.7 ug/L following a resample of ND. Footnote (2): initial color result of 22 units at Well No. 5-2 averaged down to 11 units following a resample of ND. 100% of Plainview's land lies inside a public water service area (Plainview Water District and others), per the NYS Department of Health boundaries EPA publishes. A service area is where mains run; a home inside it can still be on a private well.
Your water district
Who supplies Plainview’s water
Plainview Water District
What the numbers mean
Like most of Nassau, Plainview runs on treated public water. The day-to-day concerns here are the chlorine and chloramine used to keep the supply safe through the distribution system, plus the naturally high hardness of Long Island groundwater — the mineral content that leaves scale on fixtures and spots on glassware. Neither is an emergency, but both are exactly what point-of-entry carbon filtration and softening are designed to address.
What this means for filtration
Matching Plainview’s water to a system
For Plainview, the numbers point first to under-sink reverse osmosis, whole-house carbon filtration, and whole-house + softener combo: dissolved contaminants close to their limits.
- Recommended
Under-Sink Reverse Osmosis
Dissolved contaminants close to their limits
Nitrate averaged 8.4 mg/L with samples up to 8.4 against a 10 mg/L limit — the closest number to its limit here. It passes straight through carbon; reverse osmosis is designed to reduce it at the tap. PFOA/PFOS reached 3.27 ng/L (ppt) in at least one sample — under New York's 10 ppt limit. Whether an under-sink reverse osmosis model reduces PFOA or PFOS depends on that model's certification or performance data sheet. Perchlorate was detected up to 5.8 µg/L (limit 18).
Explore Under-Sink Reverse Osmosis - Recommended
Whole-House Carbon Filtration
Solvent traces and chlorine in the supply
Free chlorine averaged 1.03 mg/L at the entry point (limit 4), the residual that gives tap water its pool taste and dries skin and hair. Solvent traces were detected: 1,1,1-Trichloroethane up to 1.8 µg/L (limit 5 each). Whether a whole-house carbon model reduces those solvents is on that model's data sheet.
Explore Whole-House Carbon Filtration - Recommended
Whole-House + Softener Combo
Hardness 180 mg/L, about 10.5 grains per gallon
At 180 mg/L (10.5 gpg) this is hard water: it scales water heaters, spots glassware and leaves film on skin. A softener paired with carbon is the standard fix above 7 grains.
Explore Whole-House + Softener Combo
Questions
Plainview water FAQ
Nearby Nassau County towns
Free in-home test
See what’s really in your Plainview water.
Published reports cover the public supply — a free in-home test measures your taps (and your well, if you have one), then we walk you through the results.